.

MAIN PRODUCTS


 

.

Air Heaters, Radiators - Convection Heaters/Space Heaters Choice of heat sources, Steam, Thermic Fluid Oil, Hot Water or Electricity.

Capacities-500 CFM to 50000 CFM
Temp Range-Atmospheric Temp. to 80 Deg.C, 100 Deg.C, 120 Deg.C, Upto 200 Deg.C Head Load-1000 Kcal/Hr. to 1000000 Kcal/Hr.

        Data Required Along With Enquiry - 

  • Air flow rate in CFM or M3/hr.

  • Air inlet Temp.

  • Air Outlet temp. Required.

  • Heat sources etc..                                               

.

Air Coolers, Condensors - With Chilled water, Brine solution, Cooling tower water.



Capacities-1 TON to 1000 TONS


          Design Data Required-

  • Air flow rate in CFM or M3/HR. 

  • Air inlet Temp.

  • Air Outlet temp. Required, Cooling source, MOC.

 

.

Evaporating Coils - Atmospheric Type & Forced Heating Type.


Capacities-1 TON to 1000 TONS

Ideal for Argon, Oxygen, Nitrogen, Carbon Dioxide, & Other Cryognic Gases.


 

 

.

Air Heater Blower Unit
Capacities-500 CFM to 50000 CFM of Air Flow
Air Pressure-25 mm WG to 1000 mm WG, Air Temp. 50 Deg.C to 200 Deg.C
Heat Source-Steam, Thermic Fluid Oil, Hot Water or Electricity
Blowers-Centrifugal Type Blowers, with impellor statically & dynamically balanced.
Most ideal for continuous air at given pressure, purity & temperature

..


Oil Coolers With Inbuilt Fan -

Capacities-Oil Flow Rate 25 LPM to 5000 LPM
Ideal for cooling of the Oil with Atmospheric Air.
Cooling in accordance with Dry bulb temp. Of the region. Widely used where water is not available for cooling purpose.

.

Heating Coil For Standard Tray Driers
Ready to use Heating coils Driers of capacities 48 TRAYS, 96 TRAYS, 192 TRAYS & 384 180 TRAYS.

Suitable for Steam or Thermic Fluid Oil Heating.

Pressure Tested At 10 KG/CM2
Ideal For Conversions From Electrically Operated Driers To Steam Heated Or Oil Heated Models.

.

Heating Coils For Fluid Bed Driers
Ready to use Heating coils for Fluid Bed Driers of capacities of 60 kgs/hr, 100 kgs/hr, 120 kgs/hr, 180 kgs/hr, 200 kgs/hr

Suitable for Steam or Thermic Fluid Oil Heating.

Pressure Tested At 10 KG/CM2
Ideal For Conversions From Electrically Operated Driers To Steam Heated Or Oil Heated Models.







 

.

Air Cooled Heat Exchangers

Air Cooled Heat exchangers are used for cooling of Water, Oil or other fluids using air as the cooling media. This can replace the conventional cooling towers, which uses water as the cooling media. As this heat exchanger use the atmospheric air, there is no consumption of water. This type of Coolers is ideal for areas where water is costly and not available in large quantity for the Industrial use.

Induced Draft fans are installed on top of the tube bundle. Fluid to be cooled is passed through the tubes. GI or AL. Fins are used for increasing the surface area of the tubes. Tube bundle is pressure tested for leak proof operation. Impeller of the fan is dynamically & statically balanced for vibration and noise free operation. Motor is TEFC type.

.

Finned Tubes

Company makes use of various types of Finned Tubes in the manufacture of Heat Exchangers, Heating & cooling coils. Spiral wound Crimped type, L base, G type; Integral, Wire Wound & Extruded type are some of the categories of Finned tubes. Selection of the type of Finned tubes depends on the Duty condition, Temperature & Pressure of the fluids. Material for the tubes are Carbon steel, Stainless steel, Copper, Brass. Fin material will be MS, SS, Copper, Brass or Aluminium.


          

 

Company Info
Home  |   Products  |   Aboutus   |    Inquiry  |    Email   | 


Best viewed with IE 4.0 version / Netscape 4.04 or higher at 800 x 600 x 16-Bit color resolution or better.